|
|
1400475SS 3 YD. 96" STAINLESS STEEL SPREADER KIT, GAS ENGINE |
$5900.00 plus shipping |
1400475SSH 3 YD. 96" STAINLESS STEEL SPREADER KIT, HYDRAULIC DRVIE |
$5300.00 plus shipping |
1400500SS 4 YD. 108" STAINLESS STEEL SPREADER KIT, GAS ENGINE |
$6300.00 plus shipping |
1400500SSH 4 YD. 108" STAINLESS STEEL SPREADER KIT, HYDRAULIC DRVIE |
$6300.00 plus shipping |
1400550SS 4.5 YD. 120" STAINLESS STEEL SPREADER KIT, GAS ENGINE |
$6700.00 plus shipping |
1400550SSH 4.5 YD. 120" STAINLESS STEEL SPREADER KIT, HYDRAULIC DRVIE |
$6600.00 plus shipping |
OPTIONS &ACCESSORIES:
LS1 12-VOLT LIQUID SPRAY SYSTEM
LB8663SST STAINLESS STEEL D.O.T. LIGHTBAR
3008560 HOPPER SPREADER TAILGATE LOCK KIT
1496505 NYLON RATCHET STRAP MOUNTING KIT |
$1199.00 plus shipping
$259.00 plus shipping
$129.00 plus shipping
$53.00 plus shipping |
| GENERAL:
• Self contained hopper
• Spreads free flowing materials sand and/or salt
• Spread width of 4' to 30'
MATERIAL HOPPER:
• 12 gauge 304 Stainless steel with continuously welded seams.
• All hopper sides are formed with a continuous "J" channel profile for added rigidity and strength. Six (6) 12 gauge body gussets.
• Optimum material feed is maintained by hopper side walls slopped at 45°
• Heavy duty, 4 section hinged top grate is standard. Bars are ¼" diameter located on 3" center grid (installed).
• Built-in four corner lift loops.
CONVEYOR:
• Conveyor is 12½" wide, all steel pintle chain type (#667H Pitch), with 1/4" x 1" crossbars on 4-5⁄8" centers.
• Replaceable 10 gauge stainless steel chain shields.
• Replaceable 10 gauge stainless steel conveyor floor.
• 10 gauge stainless steel inverted Vee
• Conveyor driven by 20:1 ratio worm gearbox utilizing tapered bearings
• Conveyor chain is adjustable for chain take up, providing optimum performance and drive life.
• Chain drive and idler sprockets are 6-tooth cast sprockets keyed to 1¼" shafts.
• Conveyor chain wiper minimizes waste.
SPINNER ASSEMBLY:
• Spinner chute has two adjustable internal baffles
• Four (4) external baffles (3 adjustable, 1 fixed)
• 18" x ¾" thick polyurethane spinner disc
• Bolt-on spinner housing minimizes replacement cost.
POWER SOURCE:
• Gas Engine: 10.5 horsepower, Briggs & Stratton Intek |
|
1450757SSH 7 YD "LEVEL" HYDRAULIC DRIVE SPREADER W/ 50:1 GEARBOX |
$9500.00 plus shipping |
1425757SSH 7 YD "LEVEL" HYDRAULIC DRIVE SPREADER W/ 25:1 GEARBOX |
$9500.00 plus shipping |
1450863SSH 8.3 YD "LEVEL" HYDRAULIC DRIVE SPREADER W/ 50:1 GEARBOX |
$10300.00 plus shipping |
1425863SSH 8.3 YD "LEVEL" HYDRAULIC DRIVE SPREADER W/ 25:1 GEARBOX |
$10300.00 plus shipping |
1450969SSH 9.6 YD "LEVEL" HYDRAULIC DRIVE SPREADER W/ 50:1 GEARBOX |
$10700.00 plus shipping |
1425969SSH 9.6 YD "LEVEL" HYDRAULIC DRIVE SPREADER W/ 25:1 GEARBOX |
$10700.00 plus shipping |
| GENERAL:
• Self-contained hopper.
• Spreads free flowing materials sand and/or salt.
• Spread width of 4’ to 40’.
MATERIAL HOPPER:
• 7-gauge 304 stainless steel cross members.
• 10-gauge 304 stainless steel, long sills with rear enclosure & integral chain shields.
• 10-gauge 304 stainless steel replaceable floor.
• 10-gauge 304 stainless steel sides (continuously welded seams), gussets and rear panel.
• 10-gauge 304 stainless steel front panel.
• Four (4) 5/8” thick lift points.
FEEDGATE:
• 10-gauge, 304 stainless steel with scaled screw jack adjustment.
• 18-5/8" W x 10" T opening.
CONVEYOR:
• 24" wide, pintle chain conveyor with 3/8" thick x 1-1/2" wide crossbars on 4-1/2” centers (667X Pitch).
• 2" diameter drive shaft with 4-bolt relubeable bearing.
• 8-tooth cast iron sprockets.
• 50:1 or 25:1 direct-drive gearbox with extended through-shaft for ground speed sensor.
• 1-1/2" diameter idler shaft with 4" adjustable range relubeable bearing.
• Conveyor chain wiper made of belted rubber minimizes waste.
STANDARD INSTALLED EQUIPMENT:
• 4-section hinged top grate screens. 3/8" diameter bar on 3" centers with 1/4" x 2" x 2" angle iron frame. Hinged to 6" horizontal cross beam.
• 10-gauge, 304 stainless steel inverted “V” prevents material compaction and reduces wear on drive train components.
CHUTE/SPINNER ASSEMBLY:
• 10-gauge, 304 stainless steel laser cut parts with smooth radius corners.
• Telescopic adjustment in 3" increments to accommodate varying body mounting heights.
• Two (2) adjustable, internal baffles direct material to 20" diameter x 5/8" thick, 6 fin poly spinner disc.
• Three (3) adjustable external and one (1) fixed deflector with overlapping corners provide a precision spread pattern.
• Top-mounted, direct-drive hydraulic spinner motor provides better ground clearance and corrosion protection.
• Two (2) stainless steel spring latches quick release hinged chute for bulk material unloading and convenient ground storage.
POWER SOURCE:
• Hydraulic Drive: Two independent direct drive hydraulic motors (17 GPM @ 1,500 PSI).
DIMENSIONS:
• Hopper length, 120"; Overall length, 143"; Width, 82"; Recommended use, dump bodies and flat beds with a minimum 26,000 lbs. GVW chassis.
|
|
|
